1/22/2024 0 Comments Limb drop away arrow rest![]() ![]() Unlike the easy set up of a limb-driven rest, cable-driven rests require the cables to be set up in perfect time with each other to work correctly. A cable driven rest might just be your best option for achieving optimal accuracy, but with a slight drawback. As the bus cable moves downward, the resting cable moves with it, pulling the arrow rest with it. This time, the cable attaches to the down moving cable, or the bus cable, on the bow. Limb driven rests are easy to repair on the fly since you typically only need to replace the string if something gets snagged. Once released, the limb moves back into place and the arrow rest drops. Using a cable that attaches to the bottom or top limb of your bow, you can move the limb inward as you draw your bow. Below we will detail more about the two main types of drop away rest cable driven and limb driven. Because of this, drop away rests tend to provide a more accurate shot. Instead of remaining in place after you fire your shot, a drop away arrow rest will drop down once you fire your shot, meaning the arrow is technically shot from mid air. Rest easy knowing you chose the right arrow rest! Different Types of Compound Bow Arrow Rests Drop Away Restsĭrop away arrow rests are relatively new, but have become an immediate favorite for many long time bowhunters. We will attempt to demystify your choices so you can make the most informed purchase possible. Just like many compound bow accessories on the market today, you certainly aren’t short on options. The majority of archers use one to improve their accuracy, and they are vital for the beginner archer. A compound bow arrow rest supports your arrow for the duration of your shot, giving you a chance to take aim and fire the perfect shot. The easy installation and increased accuracy are well worth it! For more information on this rest and other VaporTrail products, visit them at. If you are in the market for a new rest this year, definitely give the Limb Driver Pro or the Limb Driver Pro V a try. The installation is much easier compared to a cable driven rest and at full draw, you aren’t putting any unnecessary tension on the touchy cable system. We were surprised at how much easier bows tuned after installing this limb driven rest. The Limb Driver Pro is a great rest that supports the arrow when you need it. The four shots through the paper below were our first four shots with the Limb Driver Pro…. After we installed the Limb Driver Pro, the quality of our rips were practically perfect. We did get it close, but the consistency just wasn’t there. With the Prime Logic that we used in the video, we struggled a little when trying to achieve the perfect bullet hole with our bare shaft arrows. In the video below, you’ll notice how fast the drop away drops and you will notice that the arrow does indeed start to “nose” down a bit. Typically extra special attention has to be taken with the location of the D Loop in order to time the push through the fall of the arrow tip. This can create a bit of a tuning nightmare for some. That problem is that they drop away too fast and the arrow noses down before maximum forward motion is achieved. Thanks to a good look at arrow rest performance at 1,000 frames per second, we have identified a problem that occurs when a cable driven fall away rest is installed on certain bows. The Limb Driver Pro performs great due to the amount of time it supports the arrow during the power stroke of the shot. Tighten the set screw to lock the activation cord in place.įor a more in depth look at how to install the Limb Driver Pro, watch the video below.Thread the activation cord through the rest and pull up on the lever arm with moderate pressure.Tie the activation cord around the upper limb by using the standard D-Loop style knot.Make sure you have clearance from the cam rotation during the shot. ![]() Install the self adhesive activation cord to the top limb on the outside edge above the rest and at the forward edge of the cam.Set your preferred centershot and rest elevation.Squarely attach the rest to the bow by installing the main screw into the berger hole.The simplified version is: the rest goes from down before the shot to up at full draw and back to the down position after the shot.įollow these steps to install the Limb Driver Pro arrow rest. The rest will remain in the upward position until the bow is shot and the upper limb springs back to its normal position thus returning tension to the activation cord therefore pulling the rest back to the down position. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |